Weavers Home Page
Carbide Tipped Saw Blade Special!!
Contact, Catalog Index

tenon jigs and
hold downs - manual

SYSTEMS & EQUIPMENT JIGS & FIXTURES CUTTERS & SUPPLIES SERVICE & SUPPORT
... return to jigs, fixtures and accessories page

With a good shaper and proper, correctly adjusted shaper setups, stile & rail door parts that fit and look right, are made quickly and easily. 

The tenon setup, including the tenon jig is a crucial part of making your doors.   

Since the tenon is cut on narrow stock across the grain - the cut must be clean and the stock held square and level all the way through the cutter. 

Practically, you must have a good shaper with a true cutting spindle, good cope & stick cutters sharp and matched, and you must have a good jig that will hold up under the load of continuous work.  Then the tenon joints are tight and in accurate alignment every time. 

The jig needs a way to quickly secure the stock and clamp it with out wasting time.  It is necessary to have the guide bar on the jig riding in your shaper's miter slot,  adjusted for square and having no play in the groove. 

Weaver's coping cut (or, tenon) jigs are an essential part of your door production.


HOLD DOWNS
COPING HOLD DOWNS
RAISED PANEL HOLD DOWN
FLAT MOUNT RAISED PANEL HOLD DOWN / DUST SHEILD COMBINATION  
GENERAL HOLD DOWN

DRAWER FRONT HOLD DOWN
GENERAL HOLD DOWN
DUST SHIELDS



MANUAL TENONING JIGS


Coping Hold Down Jig for end cut

Other Items: 
Manual Rail & Panel Jigs
Air Rail & Panel Jigs
AIR TENONING JIGS

WOOD_blokTenon.GIF (2004 bytes)


cope / end / tenon cut

MANUAL COPING HOLD DOWN TENON JIG

This jig has been a workhorse for 30 years at the Weavers.   The jig is designed to cut tenons ("cross grain, rail end, cope cut") for production door manufacturers. 

This sliding hold down or "sled" can accept stock of different widths while you maintain pressure on the stock.  The Coping Jig travels in your shaper table's miter slot to make any coping cut faster and safer.  The quick action pressure bar is hand operated and there is a shield to protect your hand from the cutter.  It will handle material up to 6" wide (HD225) and 10" wide (HD226) and 2-1/4" thick. 

To prevent chipping of the wood the sled has a built in wooden block behind the workpiece that keeps the back end of the cut from blowing out as you come out of the cutter.  ("blowout"), there is a backup wood block (Bolted On).   And, to protect your wood from marring there is a rubber pad on the steel pressure plate.

Note: Success in the tenon cut is the jig, material, and the "blowout block" (or "back up block") be square with the tenon fence or tenon guide. There are also allen screws ("set screws") in the guide bar for fine adjustment to ensure fit and square with your shaper's miter slot (or groove). Also, there are squaring bolts for the blowout block.


Tenon (Coping) Hold Down - counter clockwise cutter rotation
                                            pushing the jig from right to left)
   Item No.    Width                                  Price
    HD225        6"                                    $295
    (for left handed +$20.00  - clockwise cutter rotation
                                              pushing the jig from left to right)

Tenon (Coping) Hold Down (Large) - counter clockwise cutter rotation
                                                        pushing the jig from left to right)
   Item No.    Width                                  Price
    HD226        10"                                   $379
    (for left handed +$20.00  - clockwise cutter rotation
                                               pushing the jig from right to left)

 

placeholder2f.gif (833 bytes)
(coping hold down on a weaver shaper)

HD225 Tenon Hold Down - $295 

placeholder2f.gif (833 bytes)placeholder2f.gif (833 bytes) 

 Drawer Ends Hold Down


(drawer front endsd hold down on a weaver shaper)
HD222 Drawer Front Ends Hold Down - $169
placeholder2f.gif (833 bytes)
 


FE53 Split Tenon Fence - use with one cutter head     $179


FE25 Continuous Tenon Fence - use with two head cutter stack    $179

The fence has continuous protection in front of the cutter so that small/narrow parts don't get pulled in.

placeholder2f.gif (833 bytes)

CALL TOLL FREE 1-800-255-6214
Phone (913) 831-1800 Fax (913)831-2974 
Canada 1-800-255-6214  
Mexico 001-800-010-0136  

SYSTEMS & EQUIPMENT JIGS & FIXTURES CUTTERS & SUPPLIES SERVICE & SUPPORT

Click to go to top of this page. 
Back to Weavers Home Page
See our Carbide Tipped Saw Blade Special!!
Contact, Catalog Index